Setting Cisco Switch 2960G 24TC-L


Would you like to terminate autoinstall? [yes]: Y


--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no

Switch>ena
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname Switch1
Switch1(config)#enable secret xxxxx
Switch1(config)#service password-encryption
Switch1(config)#username admin password xxxxx
Switch1(config)#exit

Switch1#configure t
Enter configuration commands, one per line. End with CNTL/Z.
Switch1(config)#vtp mode transparent
Setting device to VTP TRANSPARENT mode.
Switch1(config)#spanning-tree mode pvst
Switch1(config)#end

Switch1#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.

Switch1(vlan)#vlan 200 name internal
VLAN 200 added:
Name: internal
Switch1(vlan)#vlan 201 name eksternal
VLAN 201 added:
Name: eksternal
Switch1(vlan)#vlan 202 name DMZ
VLAN 202 added:
Name: DMZ

Switch1(vlan)#exit
APPLY completed.

Switch1#configure t
Enter configuration commands, one per line. End with CNTL/Z.

Switch1(config)#interface GigabitEthernet0/1
Switch1(config-if)# description webcore-papp
Switch1(config-if)# switchport access vlan 200
Switch1(config-if)# switchport mode access
Switch1(config-if)# no shutdown
Switch1(config-if)# spanning-tree portfast
Switch1(config-if)#!

-----------------------------------------------

Switch1(config)# interface GigabitEthernet0/21
Switch1(config-if)# description Trunk_To_BIGIP1
Switch1(config-if)# media-type r
Switch1(config-if)# switchport trunk allowed vlan 200,201,202
Switch1(config-if)# no shutdown
Switch1(config-if)# switchport mode trunk
Switch1(config-if)#!

Switch1(config)# interface GigabitEthernet0/22
Switch1(config-if)# description Access_To_Switch_Outer
Switch1(config-if)# media-type r
Switch1(config-if)# switchport access vlan 201
Switch1(config-if)# switchport mode access
Switch1(config-if)# no shutdown
Switch1(config-if)#!

Switch1(config)#interface GigabitEthernet0/23
Switch1(config-if)# description Trunk_To_Switch_Outer_CAT1
Switch1(config-if)# media-type r
Switch1(config-if)# switchport trunk allowed vlan 201,202
Switch1(config-if)# no shutdown
Switch1(config-if)# switchport mode trunk
Switch1(config-if)#!

Switch1(config)#interface GigabitEthernet0/24
Switch1(config-if)# description Trunk_To_Switch_Outer_CAT2
Switch1(config-if)# media-type r
Switch1(config-if)# switchport trunk allowed vlan 201,202
Switch1(config-if)# no shutdown
Switch1(config-if)# switchport mode trunk
Switch1(config-if)#!


Switch1(config-if)#exit

Switch1(config)#interface vlan200
Switch1(config-if)#ip address 192.168.10.1 255.255.255.0
Switch1(config-if)#no shut
Switch1(config-if)#exit

Switch1(config)#ip default-gateway 192.168.20.1
Switch1(config)#no ip http server
Switch1(config)#ntp server 192.168.20.1

Switch1(config)#line con 0
Switch1(config-line)# login local
Switch1(config-line)#line vty 0 4
Switch1(config-line)# login local
Switch1(config-line)#line vty 5 15
Switch1(config-line)# login local
Switch1(config-line)#exit
Switch1(config)#end

Thanks to Mas Hansen for helping me.

Popular posts from this blog

Howto configure boot device order on ILOM

To ensure the system can be installed using the DVD drive, the boot device order in the BIOS has to be configured correctly so that the DVD drive takes precedence over the internal hard drives. 1 Log into the ILOM. 2 Start the system if it is not already running: > start /SYS else reset the system: > reset /SYS 3 Log onto the system’s console: > start /SP/console 4 When prompted, press Esc 2 to enter setup. 5 Once the setup menu has loaded, navigate across to the Boot screen by using the right arrow key. 6 Using the down arrow key, select the Boot Device Priority item and press Enter. 7 Confirm that the item [CD/DVD] is higher in the list than the item [Hard Drive]. The order can be changed by selecting the relevant item and using the +/- keys to move the item up or down in the list. 8 Once the order is correct, save any changes made by pressing Esc and then navigate right to the Exit screen. Select the item Save Changes and Exit and press Enter, then confirm...
Read more

Installing Depot files on HP-UX 11.23 ia64

Download your depot files from http://hpux.connect.org.uk/ based on your machine type. Download it, for example : bash-3.2-ia64-11.23.depot.gz, put it on /tmp. Install it with 2 option : 1. It will display SAM # swinstall -s /tmp/bash-3.2-ia64-11.23.depot.gz 2. It don't display SAM, so you get quick way # swinstall -s /tmp/bash-3.2-ia64-11.23.depot.gz bash Don't forget to install dependencies for this depot file, it's different from Redhat, who will reject rpm that missed dependencies. HP-UX accept all depots without any warning, but you must install dependencies yourself. You can know dependencies on http://hpux.connect.org.uk/, when you download, look at any dependencies for this depot file. Check depot files that already installed on your system # swlist Somehow any error happened when installing from directory another than /tmp, for example : /data. You should register that directory to depot. # cd /data # swreg -l depot `pwd` If it still fails, look at my post before a...
Read more

SAN Switch Config Command

Login via console Fabric OS (swd77) swd77 console login: admin Password: Note: password default is "password" - set hostname swd77:admin> switchName swcdr1 Committing configuration... Done. swcdr1:admin> - set IP Address swcdr1:admin> ipaddrset Ethernet IP Address [192.168.0.25]: 192.168.0.11 Ethernet Subnetmask [255.255.255.0]: Fibre Channel IP Address [0.0.0.0]: Fibre Channel Subnetmask [0.0.0.0]: Gateway IP Address [192.168.0.25]: 0.0.0.0 Issuing gratuitous ARP...Done. 2008/07/14-18:46:43, [WEBD-1007], 494,, INFO, swcdr1, HTTP server will be restarted due to change of IP Address IP address is being changed...Done. Committing configuration...Done. - Configure basic parameter swcdr1:admin> switchDisable swcdr1:admin> configure Configure... Fabric parameters (yes, y, no, n): [no] y Domain: (1..239) [1] 22008/07/14-18:50:40, [FW-1424], 24,, WARNING, swcdr1, Switch status changed from HEALTHY to MARGINAL. 2008/07/14-18:50:40, [FW-1439], 25,, WARNING, swcdr...
Read more